Self-Levelling Compound vs Screed: Which Floor Preparation Does Your Project Need?
Every great floor finish starts with what lies beneath it. Large-format tiles, vinyl planks, epoxy coatings and wooden floors all need a sound, flat base. If the substrate is uneven, you get lippage between tiles, hollow spots, cracking and visible bumps under thin flooring.
The two most common ways to prepare a floor are a screed and a self-levelling compound. They are often confused, but they do very different jobs. This guide explains the difference and helps you decide which one your project needs.
What Is a Floor Screed?
A screed is a layer of cement-sand mortar, or a pre-bagged screed product, laid over a concrete slab. It is spread and compacted by hand, then finished with a straight edge and float.
Screeds are mainly used to:
- Build up floor levels to the required height
- Create falls towards drains in bathrooms, balconies and terraces
- Cover pipes and underfloor heating
- Provide a solid base for finishes on new construction
Traditional screeds are usually laid in thicker layers than self-levelling compounds, and they need time to dry before moisture-sensitive finishes are applied.
What Is a Self-Levelling Compound?
A self-levelling compound is a flowable, cement-based or gypsum-based material that is poured onto the floor and spreads under its own weight to form a smooth, flat surface. It is typically applied in thin layers, often only a few millimetres thick, depending on the product.
Self-levelling compounds are used to:
- Smooth minor unevenness in existing screeds or slabs
- Create a very flat base for thin finishes like vinyl, carpet tiles or epoxy
- Prepare floors for large-format tiles, where flatness is critical
- Renovate old floors quickly
Many products dry fast enough for light foot traffic within hours, which helps fast-track renovation work. Our guide on how self-levelling flooring materials create smooth and durable surfaces explains how they work in more detail.
Self-Levelling Compound vs Screed: Key Differences
| Factor | Floor screed | Self-levelling compound |
|---|---|---|
| Main purpose | Build levels and falls | Create a smooth, flat surface |
| Typical thickness | Thicker layers | Thin layers |
| Application | Spread and compacted by hand | Poured and flows into place |
| Creates slopes to drains | Yes | No, it levels flat |
| Surface flatness | Good | Excellent |
| Speed | Slower to lay and dry | Fast application, often fast drying |
The most important difference is slope. A self-levelling compound naturally finds a flat level, so it cannot create falls towards a floor drain. In showers, balconies and wet areas, a sloped screed is needed first.
When to Use Each
Choose a screed when you need to:
- Raise the floor level significantly
- Create falls towards floor drains or shower drains
- Embed services or underfloor heating
- Lay a base on new construction
Choose a self-levelling compound when you need to:
- Correct small imperfections in an existing floor
- Achieve maximum flatness before vinyl, epoxy or large-format tiles
- Renovate quickly with minimal downtime
On many projects, the best result comes from using both: a screed for levels and falls, followed by a self-levelling layer where a perfectly flat finish is needed. Explore our full range of screed and self-levelling materials.
Preparation Tips for Self-Levelling Compounds
- Check the base: It must be sound, clean and free of dust, grease and loose material.
- Prime the surface: Use the recommended primer to control absorption and prevent pinholes and air bubbles.
- Seal gaps: Block edges, doorways and cracks so the compound does not escape.
- Mix accurately: Use the exact water quantity stated by the manufacturer. Too much water weakens the surface and causes cracking.
- Pour continuously: Work in strips and keep a wet edge, using a spiked roller to release trapped air.
- Protect while curing: Shield the floor from direct sun, strong draughts and heat, which can cause rapid drying in UAE conditions.
Don’t Forget Waterproofing and Walls
Floors in wet areas still need a waterproofing membrane over the screed before tiling. For walls, a factory-blended plaster such as Saveto Ready Mix Plaster gives an equally consistent base for tiling or painting.
Conclusion
Screeds and self-levelling compounds are not competitors but partners. Use a screed to build height, cover services and create falls, and a self-levelling compound to deliver a smooth, flat surface for demanding finishes. Choosing correctly prevents cracked tiles, uneven vinyl and costly rework. Contact Crete Pro Trading for screeds, self-levelling compounds and technical advice across the UAE.
Frequently Asked Questions
1. What is the difference between screed and self-levelling compound?
Screed is a thicker mortar layer spread by hand to build levels and create falls. Self-levelling compound is a flowable material poured in thin layers to create a very smooth, flat surface.
2. Can self-levelling compound be used to create a slope to a drain?
No. Self-levelling compound flows to a flat level, so it cannot form falls. Use a sloped screed in showers, balconies and other areas with drains.
3. Do I need to prime before applying self-levelling compound?
Yes, priming is usually required. It controls absorption, improves bonding and reduces air bubbles and pinholes. Follow the manufacturer’s primer recommendation.
4. Can I tile directly on self-levelling compound?
In most cases, yes, once it has cured according to the data sheet. Choose a tile adhesive compatible with the compound, especially for gypsum-based products.
5. How long does self-levelling compound take to dry?
Drying time depends on the product, thickness and site conditions. Many compounds allow light foot traffic within hours, but always follow the data sheet before installing final flooring.

Cretepro Building Material Trading LLC is the authorized importer, distributor and Trader of many well-known leading brands for Construction Chemicals, Building Maintenance and Allied products.